Skip to content
Aultra Tools
Free VPN

MM to Inches Converter

An inch is exactly 25.4 millimeters, so divide millimeters by 25.4: 10 mm ≈ 0.3937 in. For tools and tape measures the converter also gives the nearest fraction, down to 1/64 inch, and how far that fraction is from your size.

10 mm ≈ 0.393701 in

Rounded
10 mm ≈ 0.393701 in

As a fraction of an inch

≈ 3/8 in

The mark is 0.48 mm shorter than your value.

0 in1 in
Units

10 mm in other units

Inches (in)
0.393701 in
Feet (ft)
0.0328084 ft
Feet + inches
0.39 in
Yards (yd)
0.0109361 yd
Miles (mi)
0.00000621371 mi
Centimeters (cm)
1 cm
Meters (m)
0.01 m
Kilometers (km)
0.00001 km
Nautical miles (nmi)
0.00000539957 nmi

Make a chart: Millimeters (mm) to Inches (in)

In millimeters.

Millimeters (mm)Inches (in)Nearest 1/16 in
10.03937011/16 in
20.07874021/16 in
30.118111/8 in
40.157483/16 in
50.196853/16 in
60.236221/4 in
70.2755911/4 in
80.3149615/16 in
90.3543313/8 in
100.3937013/8 in
110.4330717/16 in
120.4724411/2 in
130.5118111/2 in
140.5511819/16 in
150.5905519/16 in
160.6299215/8 in
170.66929111/16 in
180.70866111/16 in
190.7480313/4 in
200.78740213/16 in
210.82677213/16 in
220.8661427/8 in
230.9055127/8 in
240.94488215/16 in
250.9842521 in

Converted on your device. Nothing you type is sent anywhere.

How to convert mm to inches

Divide the millimeters by 25.4. A 6 mm bolt is 6 ÷ 25.4 = 0.2362 in, and a 100 mm pipe is 3.937 in.

Inch tools are sized in fractions, and almost no metric size lands exactly on one. The useful questions are which fraction is nearest and how big the gap is. 10 mm is 0.3937 in. The nearest sixty-fourth is 25/64 in, which is 9.922 mm: 0.078 mm short of 10 mm.

  1. Divide the millimeters by 25.4 for decimal inches.
  2. Choose the precision of your tool: 1/16 for a tape measure, 1/32 or 1/64 for drill bits.
  3. Multiply the decimal part by that number and round to a whole number: that is the top of the fraction.
  4. Check the gap in millimeters before you rely on the fraction for a fit.

MM to inches chart

Millimeters to inches, 1 to 25 mm

mmInchesNearest 1/64 inNearest 1/16 in
10.03943/641/16
20.07875/641/16
30.11811/81/8
40.15755/323/16
50.196913/643/16
60.236215/641/4
70.27569/321/4
80.31505/165/16
90.354323/643/8
100.393725/643/8
110.43317/167/16
120.472415/321/2
130.511833/641/2
140.551235/649/16
150.590619/329/16
160.62995/85/8
170.669343/6411/16
180.708745/6411/16
190.74803/43/4
200.787425/3213/16
210.826853/6413/16
220.866155/647/8
230.905529/327/8
240.944915/1615/16
250.984363/641

Metric wrench sizes and the closest inch size

A wrench has to be the same size as the nut or a touch bigger. Where the inch size in the last column is smaller than the metric size, it will not go on.

Metric size (mm)InchesClosest 1/16 inThat inch size in mm
60.2361/46.35
70.2761/46.35
80.3155/167.94
100.3943/89.53
110.4337/1611.11
120.4721/212.70
130.5121/212.70
140.5519/1614.29
170.66911/1617.46
190.7483/419.05
220.8667/822.23
240.94515/1623.81

Need other values? Set the first value, the last value and the step under “Make a chart” in the converter at the top of this page, then print the chart or download it as a spreadsheet file.

Worked examples

What is 10 mm in inches as a fraction?

10 mm ≈ 0.3937 in. To the nearest 1/64 that is 25/64 in (9.92 mm). To the nearest 1/16 it is 3/8 in, which is only 9.525 mm: almost half a millimeter small, so a 3/8 inch wrench will not fit a 10 mm nut.

Is 12 mm the same as 1/2 inch?

No. Half an inch is 12.7 mm, so 12 mm is 0.7 mm smaller. A 12 mm hole is too tight for a 1/2 inch bolt.

How thick is 3 mm in inches?

3 mm ≈ 0.118 in, a little under 1/8 inch, which is 3.175 mm. Glass, acrylic and plywood are sold under both names, but the two thicknesses are 0.175 mm apart.

What is 50 mm in inches?

50 mm ≈ 1.969 in, just under 2 inches (50.8 mm). Lenses, pipe and timber are often named by a round metric size like this one.

Common mix-ups with millimeters and inches

  • mm and “mil”. In the US a mil is a thousandth of an inch (0.0254 mm), used for plastic sheeting and coatings. In everyday British speech “mil” often means a millimeter. A 6 mil sheet is 0.152 mm thick, not 6 mm.
  • Named sizes. A US “2 by 4” measures 1 1/2 by 3 1/2 inches (38.1 mm by 88.9 mm). Measure the part instead of converting its name.
  • Close is not equal. 8 mm and 5/16 inch differ by 0.0625 mm, close enough for a wrench. 13 mm and 1/2 inch differ by 0.3 mm, enough to slip and round off a tight nut.

A quick way to do it in your head

Multiply the millimeters by 4 and move the decimal point two places to the left: 25 mm × 4 = 100, so about 1 inch. This treats an inch as 25 mm and is 1.6% high. Three sizes are worth remembering exactly: 25.4 mm is 1 inch, 12.7 mm is 1/2 inch and 6.35 mm is 1/4 inch.

Definitions and sources

Millimeter (mm)
One thousandth of a metre. Spelled “millimetre” outside the US.
Inch (in)
Exactly 2.54 cm. It is 1/36 of the international yard, which the US, the UK and other countries fixed at 0.9144 m in 1959.

Every figure on this page is worked out from these definitions, not from rounded conversion factors, and is rounded only when it is shown. A result marked “Exact” is the complete value. The definitions were last checked against their sources on 18 November 2026:

Related conversions

Frequently asked questions

How many mm are in an inch?
Exactly 25.4. The inch is defined as 2.54 centimeters, and there are 10 millimeters in a centimeter.
How do I read the “nearest fraction” result?
It is the mark on an inch ruler closest to your size at the precision you choose, from 1/2 down to 1/64 inch. Beside it is the gap in millimeters, so you can judge whether the fraction is close enough for the job. The green line on the ruler is that mark and the pointer is your exact size.
What is 1/64 of an inch in mm?
1/64 in = 0.396875 mm. It is the finest mark on most inch rulers, so a fraction rounded to the nearest 1/64 is never more than about 0.2 mm from the true size.
Is 6 mm the same as 1/4 inch?
No. A quarter of an inch is 6.35 mm, so 6 mm is 0.35 mm smaller. They are often treated as the same size for hose and tubing, where the fit is not tight.

Last updated: 2026-11-19